Search Results

Large Eddy Simulations (LES) and tracer-based Laser-Induced Fluorescence (LIF) measurements were performed to study the dynamics of fuel wall-films on the piston top of an optically accessible, four-valve pent-roof GDI research engine for a total of eight operating conditions. Starting from a reference point, the systematic variations include changes in engine speed (600; 1,200 and 2,000 RPM) and load (1000 and 500 mbar intake pressure); concerning the fuel path the Start Of Injection (SOI=360°, 390° and 420° CA after gas exchange TDC) as well as the injection pressure (10, 20 and 35 MPa) were varied. For each condition, 40 experimental images were acquired phase-locked at 10° CA intervals after SOI, showing the wall-film dynamics in terms of spatial extent, thickness and temperature.

In this study, numerical simulations of in-cylinder processes associated to fuel post-injection in a diesel engine operated at Low Temperature Combustion (LTC) have been performed. An extended Conditional Moment Closure (CMC) model capable of accounting for an arbitrary number of subsequent injections has been employed: instead of a three-feed system, the problem has been described as a sequential two-feed system, using the total mixture fraction as the conditioning scalar. A reduced n-heptane chemical mechanism coupled with a two-equation soot model is employed. Numerical results have been validated with measurements from the optically accessible heavy-duty diesel engine installed at Sandia National Laboratories by comparing apparent heat release rate (AHRR) and in-cylinder soot mass evolutions for three different start of main injection, and a wide range of post injection dwell times.

This study presents an application of the conditional moment closure (CMC) combustion model to marine diesel sprays. In particular, the influence of fuel evaporation terms has been investigated for the CMC modeling framework. This is motivated by the fact that substantial overlap between the dense fuel spray and flame area is encountered for sprays in typical large two-stroke marine diesel engines which employ fuel injectors with orifice diameters of the order of one millimeter. Simulation results are first validated by means of experimental data from the Wärtsilä optically accessible marine spray combustion chamber in terms of non-reactive macroscopic spray development. Subsequently, reactive calculations are carried out and validated in terms of ignition delay time, ignition location, flame lift-off length and temporal evolution of the flame region. Finally, the influence of droplet terms on spray combustion is analyzed in detail.

It is well-known that the spatial distribution of turbulence intensity and fuel concentration at spark-time play a pivotal role on the flame development within the pre-chamber in gas engines equipped with a scavenged pre-chamber. The combustion within the pre-chamber is in turn a determining factor in terms of combustion behaviour in the main chamber, and accordingly it influences the engine efficiency as well as pollutant emissions such as NOx and unburned hydrocarbons. This paper presents a numerical analysis of fuel concentration and turbulence distribution at spark time for an automotive-sized scavenged pre-chamber mounted at the head of a rapid compression-expansion machine (RCEM). Two different pre-chamber orifice orientations are considered: straight and tilted nozzles. The latter introduce a swirling flow within the pre-chamber. Simulations have been carried out using with two different turbulence models: Reynolds-Averaged Navier-Stokes (RANS) and Large-Eddy Simulation (LES).

Optical soot pyrometry is a mature experimental technique that has been applied to a broad range of combustion systems for measuring soot temperature and concentration. Even though the method is widely used and well documented, the line of sight nature of the technique makes the interpretation of its results challenging. Notably, gradients in temperature and soot concentration along the line of sight or across the field of view can introduce significant levels of uncertainty in the results. This paper presents a numerical study where the signal from the experimental two-color pyrometry technique in a marine diesel engine reference experiment is reconstructed employing computational fluid dynamics (CFD) and a detailed Line-by-Line (LBL) spectral radiation model. The analysis is aimed at qualitatively supporting interpretability of experimental observations.

This paper presents a phenomenological single-zone combustion model which meets the particular requirements of high speed DI diesel engines with common rail injection. Therefore the model takes into account the freely selectable pilot and main injection and is strongly focusing on result parameters like combustion noise or NO-emission which are affected by this split injection. The premixed combustion, the mixing-controlled combustion and the ignition delay are key parts of the model. The model was developed and tested on more than 200 samples from three different engine types of DaimlerChrysler passenger car engines equipped with common rail injection. A user-friendly parameterization and a short computing time was achieved thanks to the simple structure of the model.

Combustion engines for decentralized power generation or cogeneration in general, are subject to increasingly stringent pollutant emissions regulations. Motivated by the Europe-;wide lowest allowable NOx levels in Switzerland - particularly in the Zurich metropolitan area with 50 mg/Nm3 at 5% O2 - and in close cooperation with industry, the I.C. Engines and Combustion Laboratory (LVV) of the Swiss Federal Institute of Technology Zurich (ETHZ) has investigated some new operating concepts and engine processes in order to overcome the dilemma between low emissions and high efficiency, which is usually encountered in engine optimization. Our final approach thereby involves the Exhaust Gas Recirculation (EGR) combined with stoichiometric mixture (λ = 1) and a 3-way catalytic converter. The engine is supercharged and the intake mixture aftercooled for high power density and thermal efficiency.

Oxygenated fuel additives are currently an important research topic for particulate emissions reduction in diesel engines with direct injection (DI) to meet future emission regulations. In this work more than twenty oxygenated hydrocarbons from the literature were considered as diesel fuel additives. Butylal (an acetal compound, chemical formula C9H20O2) offers significant advantages over most other oxygenates in that its physical properties are very close to those of common diesel fuel. Wear scar measurements were conducted to evaluate the lubricity characteristics of diglyme (C6H14O3), ethyldiglyme (C8H18O3), butylal and different diesel-butylal mixtures. The results reveal the low lubricity of all oxygenated compounds. Thus, for the engine tests, a lubricity improver has been added to the diesel-butylal mixtures.

Formation of soot in an auto-igniting n-dodecane spray under diesel engine relevant conditions has been investigated numerically. As opposed to research addressing turbulence-chemistry interaction (TCI) by coupling diffusive turbulence models with more sophisticated models in the context of Reynolds-Averaged Navier-Stokes equations (RANS), this study employs the advanced sub-grid scale k-equation model in the framework of a Large Eddy Simulation (LES) together with the uninvolved Direct Integration (DI) approach. A reduced n-heptane chemical mechanism has been employed and artificially accelerated in order to predict the ignition for n-dodecane accurately. Soot processes have been modelled with an extended version of the semi-empirical, two-equation model of Leung, which considers C2H2 as the soot precursor and accounts for particle inception, surface growth by C2H2 addition, oxidation by O2, oxidation by OH and particle coagulation.